The watertightness of a concrete structure
is for a big part dependent on the occurring of cracks. Due to the presence of
cracks, water can easily seep through the structure and cause leakage nuisance.
However, concrete is known for having self-healing properties in the field of
preventing leakage. When designing a concrete structure for wet environments,
engineers usually depend on the selfhealing capability of concrete for the
calculation of crack managing steel reinforcement. Yet, time after time
practice shows that very often self-healing fails with leakage as a result,
especially since the last decennia. But why is this? Why can’t we rely on the
passive self-healing capacity of concrete and what can active autonomous
healing do about this?
Let’s start with the mechanisms which
provide passive self-healing in concrete. Self-healing in concrete is known to
be caused by four processes which can occur simultaneously, but also may serve
as water tightening on their own. The techniques are the following:
a) The formation of calcium carbonate
(limestone)
b) Loose particles blocking the crack path
c) Ongoing hydration of unbound cement
particles in the crack
d) Swelling of the cement matrix
Even though these processes seem quite
self-evident, it seems to be not sufficient to fully assume watertightness.
After all, for self-healing to be able to occur by (one or more of) these
mechanisms, it has to meet some important conditions, and so has limitations.
First, the crack has to be stable. These
are typically cracks that are crossed by steel reinforcement and are considered
dormant. Unstable cracks are usually working joints, and will mostly occur
around pour breaks. Secondly, penetrating liquid should not be aggressive nor
have leaching properties. Lastly, the flow rate in the crack should not be too
large, thus the crack width shall not be too big.
Provided that the above mentioned conditions are met, autogenous healing may occur for crack widths up to 0.2 mm, according to Lohmeyer’s table, see fig 2. This table shows the relation between critical crack width and ratio of liquid head and wall thickness. The graph is based on practical observations and is accompanied by the results of two other researchers Meischner and Schiessl. But for engineers the values of Lohmeyer have the preference for practical applications, most probably because it is on the more safe side.
But why do we still see leakage in
practice? Well, the earlier mentioned four mechanisms may either be outdated or
perhaps overestimated.
Formation of calcium carbonate
The cement in concrete consist of several
products, including calcium hydroxide (Ca(OH)2). This calcium hydroxide can
react with carbon dioxide (CO2) present in the air in the crack or in the
penetrating water and form calcium carbonate (CaCO3), also known as limestone.
But it so happens that calcium hydroxide easily dissolves in water. As a
result, a part of the calcium hydroxide available on the surface of the cracks will
dissolve in the penetrating water and wash out of the crack during leakage.
Because of the highly presence of CO2 in the outside air, the calcium hydroxide
will react only at this point with CO2 and form limestone (calcium carbonate).
Therefore, the lime will precipitate on the outer surface around the crack,
rather than form inside the crack. In the pictures below, the results of
limestone formation in regular concrete is compared to concrete with active
self-healing capabilities, thus concrete with Healing Agent.
Loose particles blocking the crack path
For loose particles to be able to block the
flow path in a crack, we have to speak of quite young concrete. This may be
unbounded cement particles which can occur in only young concrete or other
loose material. In fact, it is a very weak mechanism to rely on and just assume
for loose particles to clump together and block the path. Also with higher flow
rates, the chances are small for these particles to hold on in the crack.
Ongoing hydration
Researches in the past have shown that the
capacity of autogenous healing depends on the amount of Portland cement clinker
and in particular the size of the cement particles. The coarser the cement, the
bigger the self-healing capacity of the concrete. If a crack occurs through a
big sized particle, then as a result the unbounded part of this particle will
react with the penetrating water and will hydrate, with cement stone as an end
product. This will further tighten the crack till there is no more water
available. This is the case when the crack is sealed through this phenomenon.
However, big cement particles are in contrast to the developments through the
last decades in the field of mixture compositions for low CO2 profiles and fast
strength developments. This development may be the reason why we see less
self-healing.
High amounts of CO2 emission during the
production of cement is a common discussion in the cement industry. Worldwide,
cement producers are put under pressure by the government to lower the CO2
profile of their cement. But a low CO2 profile and fast strength development,
demands binders with low clinker content and fine grind. The replacement of
clinker with ground granulated blast-furnace slag or with fly ash may lead to
less capability of self-healing. Fine grind will no longer provide unreacted
cement in a later stadium, because small particles will be fully hydrated.
Besides, continuation of the hydration process, caused by un-hydrated cement
particles, is believed not to happen. The reason for this is because the
distance between the two crack faces is generally too large to be bridged by
hydration products.
Moreover, to manage crack formation in
watertight structures, usually the cement composition will already be preferred
with less clinker to lower hydration heat which will minimize cracks. And as
mentioned above, less clinker may lead to less self-healing capability.
However, in this type of cement compositions, crack sealing may be expected in
(only) younger concrete. The slower development of cement may lead to healing
caused by ongoing hydration of remaining unreacted cement provided that there
is water available in the crack. But again, only the case in younger concrete
before it reaches the ultimate strength.
Swelling of the cement matrix
Swelling may occur when the concrete is
exposed to an environment with high relative humidity. The cement stone will
absorb water and this will cause the stone to expand. But the healing capacity
caused by swelling is actually very low and depends very much on the
environment. Studies have shown that healing caused by swelling in the cement
matrix lies between 0,005 mm to 0,01 mm. Adding swelling materials to the
matrix may lead to increase of the healing capacity. After all, they are
capable of absorbing huge amounts of water and this will lead to swelling.
Because of the absorbing property, in a later stadium they can also be used as
internal water source in concrete for healing mechanisms. Still, the healing
capacity of swelling materials in concrete is moderate and may be expected up
to 0,025 mm. As a matter of fact, swelling in concrete may cause even more
cracks as well because of internal expanding due to e.g. delayed ettringite
formation. Also, adding certain components makes it no longer subject to
autogenous healing.
Editorial supplied by BASILISK self healing concrete.
Download info pack
Download Basilisk info 8, Autogenous healing of concrete
View this article in Issue One of Concrete Trends Digital Magazine – for ease of reference this article can be found on pages 41-43
More news
- PART 2: DESIGN AND CONSTRUCTION OF SLAB-ON-GROUND: APPLYING ACI 318
- DESIGN AND CONSTRUCTION OF SLAB-ON-GROUND: APPLYING ACI 318
- DOK-ING’s innovative electric mining equipment unveiled at ElectraMining
- CONCOR’S MASTERY IN FAST TRACK PROJECT IMPLEMENTATION UNDERSCORED BY SAFETY AWARD
- PROMINENT SEA POINT HOTEL REFURBS WITH REHAU